Modern farm tractors provide most of the muscle power needed for today's high output agricultural enterprises. Tractors are more common on farms than any other piece of equipment and are used to carry mounted and semi-mounted implements, to transport equipment and materials, to pull tillage equipment and wagons and as remote power sources for other equipment Unfortunately every year, tractor accidents result in serious disabling injuries and tragic loss of life. Losses due to property damage, medical bills, time off work, reduced productivity and insurance costs are considerable. The major causes of injury and death to tractor operators are rollovers, falls and contact with tractor attachments. Statistics show that in Ontario 244 people died as a result of tractor-related accidents between 1980 and 1994. This accounted for almost 48% of the total fatalities for that period. Clearly one-half of all fatalities are caused by this agent of death. The vast majority (about half) of these fatalities were tractor rollovers to the side or the rear. During a recent eight year period in Ontario, there were more than 450 hospitalizations for accidents involving farm tractors. The average length of stay in hospital was 10 days for these injuries with a maximum for one individual of 130 days for an accident involving a power takeoff shaft contact. Manufacturers are continually improving the design of tractors to make them more safe. However, they are unable, as yet, to build in mechanisms which recognize unsafe conditions. Tractor operators who know their machine and are aware of the hazards which may occur, are better equipped to avoid a tractor mishap.
Rollovers or overturns are involved in about half of the fatal tractor accidents and are responsible for many disabling injuries and much property damage. With the use of protective frames and crush-resistant cabs with seat belts, the number of serious and fatal injuries from such accidents should decrease. Rollovers are generally due to driving too fast for conditions; striking surface hazards such as rocks, stumps and holes; running into ditches; hitching high for extra traction; driving on steep slopes; and operating front-end loaders improperly. Tractor upsets also occur when handling large round hay bales and other heavy loads with front-end loaders. Falls from moving tractors often result in serious and sometimes fatal injuries. Many times the victim is a child, but operators and adult riders can also fall. Falls often occur from smaller and/or older tractors used around the farmstead, where extra riders and overhead hazards are more common than in fields. Another cause of tractor-related death and serious injury is being caught by, or entangled in, rotating power takeoff (PTO) shafts. In most cases, the PTO shields were inadequate or had been removed. Other tractor-connected injuries and damage involve: Colliding with motor vehicles or roadside objects; Slipping and falling while mounting and dismounting; Running over bystanders; Striking overhead hazards; Being struck by flying objects, broken parts, or hydraulic fluid; Being crushed by a poorly supported tractor during repair work; Sustaining cuts, bruises, burns and other nuisance, but painful injuries, connected with maintenance and routine operation; Being overcome by exhaust gases inside closed buildings; Being burned by fires that erupt during refueling or as a result of a collision or upset. Be Physically and Mentally Fit There are numerous human factors involved in fatal tractor-related accidents. Certain factors like poor judgment, poor attitude, insufficient knowledge or training, fatigue, haste, stress, depression, intoxication, or showing off can cause a fatal tractor overturn accident. Each operator should be physically and mentally fit when operating a tractor. An operator who is sleepy, tired or not feeling well may not be able to react in time to avoid an accident. Your tractor does what you make it do. Be Properly Trained A person who does not know how to operate a tractor safely in potentially hazardous situations can be injured or killed by exercising poor judgment. Make sure all persons permitted to operate tractors have been thoroughly trained. A good place to start training is with the operator's manual. Review the operator's manual, if possible with the tractor in front of you.Be Familiar With Operator's Manual Read and follow procedures as outlined in the operator's manual. By being familiar with the operating features of a tractor, the operator will develop confidence when the tractor is driven under adverse conditions. Learn the location and purpose of all of the guages and controls as well as other indicators. Knowing where the controls are by memory can allow you to react more quickly in an emergency situation. There have been accident situations where individuals have become entangled in machinery or the power takeoff shaft and rescuers or family did not know how to disengage the equipment. Family members should be showed how to shut down equipment or disengage the PTO in case of emergency.Study the various decals on your equipment. They may point out DANGER, WARNING and CAUTION for various points on the tractor. Have an experienced tractor operator with you as you review the various decals and ask questions! A copy of all operating manuals and other relevant safety materials should be kept on file for quick reference. Use Tractor for Intended Purposes The tractor has many uses around the farm, however, improper use can result in an accident. For example, using the tractor to round up the cattle is dangerous because the operator may encounter rough, uneven ground and make sharp turns at high speeds.Check Tractor Before Operating A pre-operational check of the tractor will assure you that it is in safe operating condition. Check the tires for proper inflation and defects, windows for visibility, seat position, seat belts, brakes for adjustment, steering response, rear view mirrors, slow-moving vehicle emblem, reflectors, and running lights for day or night time operation.
Service Walkaround: Walk around the tractor a second time to check the tractor itself. This time look at the tires for wear and inflation, the power takeoff shaft for shielding and guarding (rotate the shield to make sure it moves freely), the hitch for proper hitch pin and safety clip. Pay particular attention to the ground under the tractor for any signs of liquid leaks such as oil, coolant or fuel. Check the oil: Remove the dipstick, wipe it clean and check the oil level. If oil is required, remember to wipe off the filler cap before you remove it to avoid dirt falling into the engine. Use a clean funnel and clean the top of the oil can to prevent rust or other foreign objects going in with the oil. Check the radiator: Slowly remove the red cap and check the liquid level. Check the air pre-cleaner and air cleaner. Remove and shake out any dirt. Check the fuel level. Fill if necessary, but it should have been filled at the end of the last day the tractor was used. Check the fire extinguisher. Your tractor should have a fire extinguisher in case of fire during operation or refueling. Make sure it is charged and easily accessible.
Before servicing hydraulic systems:
Yes No Are you free from the effects of drugs and alcohol? Are you wearing hearing protection? Are your close snug-fitting? Are you wearing safety glasses? Is any long hair tucked under a hat? If you answered NO to any question, DO NOT OPERATE THE TRACTOR!
Shutting down the engine:
Note: Everyone on the farm including family and employees should be taught how to safely shut off machinery. This is especially important in an accident situation. The first person on the scene must know how to shut things off. It could save a life! Take Special Care With Large Four-Wheel Drive Tractors With Articulated Steering Operating large four-wheel-drive tractors with articulated steering requires skills in addition to those necessary for operating a two-wheel-drive tractor. The operator must be especially concerned about safety because of the increased power and large dimensions of the tractor, faster speeds, and different visual perspective.
Adjust your operator's seat so that you can comfortably reach the pedals and controls. Check for visibility all around and adjust any side mirrors that you have. If mirrors or windows need cleaning, take the time to do it. You don't want an accident on the roadway because you didn't see a vehicle behind a smudge. Make sure that the operator's platform is clear of objects or debris. It is not uncommon for something to interfere with pedal operation. If your tractor is equipped with a rollover protective structure, buckle your seatbelt on before starting up. Make sure that everyone is clear from around the tractor before starting it in motion. There have been many fatalities in Ontario where small children were not seen and were run over. Sometimes you may wish to sound the horn to warn others that you are moving out. This also gives you the opportunity to test the horn before highway travel. Case History: Unaware of the two year old victim's presence, the driver of a tractor backed up and ran over the victim. When you engage the power to the drive wheels, do so slowly. Test your brakes as you start out at a slow speed. Likewise turn your steering wheel in each direction to make sure it operates as it should. Power steering should be quick and responsive. If the power steering ceases to operate, stop the tractor immediately. If a load is attached, make sure that it is hitched to the drawbar. Pulling from any point above the rear axle could cause the tractor to flip over backwards. Make sure that you are using a drawbar pin that locks in place, and is of proper size for the job at hand. Often we have seen operators trying to "make do" with a bolt or pin too small and a bump or other situation could pop the pin and cause you to lose your load. When heavy loads and equipment are attached to the rear of the tractor you may notice that the front of the tractor may start to rise. If this occurs, you should install front-end or wheel weights to help keep the tractor stable. Watch where you are going while operating the tractor, particularly near ditches and embankments, on the roadway and near obstacles such as rocks and trees. Watch for overhead powerlines, especially if you a pulling implements or a load that may come near them. If a long grain auger or other high load contacts or even comes near some lines, an electrical charge may follow the easiest path to ground which could endanger your life. Too often we hear of tractors and wagons jack-knifing. If any towed vehicle has a total weight that exceeds that of the towing tractor, then the vehicle should have independent brakes for safe operation. Use Engine Braking Using the braking power of the engine when going downhill with a heavy load can prevent a runaway tractor and overturn. By stopping and shifting to a low gear before starting downhill you will maintain good control. A rule of thumb is to use the same gear to go down a hill that you would use to pull the load uphill. Also, use a tractor large enough and with adequate braking power to control the load being pulled. If the load you are towing exceeds the weight of the towing tractor, the wagon should have independent brakes.Case History: A farm tractor was pulling a load of hay down a steep grade. After traveling approximately 85 meters down the slope, the driver prepared to turn right. The tractor veered sharply to the right and overturned, pinning the operator. Hitching Implements Properly People have been killed or seriously injured during hitching operations. Observe the following points while hitching your tractor to wagons or implements:
Take Special Care on Rough Terrain Drive around ditches and steep slopes when possible. Forward movement up a steep slope can cause a rear overturn because the center of gravity of the tractor is higher and moves toward the rear of the tractor. Backing up a steep hill or out of a ditch helps maintain stability and can save you from an overturn.Crossing slopes also can be dangerous. The operator should be alert for dips and raises that could trigger an overturn. If the tractor becomes unstable while operating on a slope, avoid an overturn and regain stability by turning down grade. Some farms may have other 'obstacles' to contend with such as small bridges over creeks or paths over railway lines. Small bridges should be constructed in such a way that they are capable of handling the weight of your tractor and whatever implements and load you are towing. The bridge you construct should also have bullrails (boards along the edges) to prevent the tractor wheels going off the side. Make sure the bridge is wide enough and always try to approach it straight on when possible, lining up trailing equipment. Most tractors sold today in Ontario come equipped with Rollover Protective Structures (ROPS) and seatbelts. ROPS have been around for about thirty years and have saved many lives in rollover situations that could have ended in tragedy. Rollover protective structures are engineered for each specific tractor and must meet national and international standards. The structure protects you by limiting a rear rollover to 90 degrees and when used in conjunction with the seatbelt, keeps you within a "frame of safety", preventing you from being tossed about the cab or from the tractor.One should never drill holes into or alter the rollover frame in any way. Some people have been known to drill holes to mount radios etc. This practice is dangerous. The ROPS structure becomes weaker at that point and in the event of a rollover, it could cave-in or collapse, not offering total protection to the operator. ROPS can be either a protective frame that is highly visible or built into a cab structure. Rollover protective structures are available for many older tractors as well. Check with your dealer or manufacturer to determine if one exists for your tractor. In recent years, many manufacturers have reduced the cost of ROPS or subsidized the installation of them. All tractor operators should be aware that a tractor is sensitive to any shift of its centre or gravity or balancing point. This is the point around which all tractor weight balances and is found on most tractors just ahead of the operator's seat and just above the height of the rear axle. different forces and practices can cause the stability of the tractor to change.These include: Centrifugal force is a force that tends to resist a change in direction. If a tractor was traveling in a straight line then suddenly turned, there would be a tendency for the tractor to want to continue in that straight line. This is centrifugal force. By doubling the tractor's speed, the centrifugal force is increased four times. Raising a load such as with a front end loader, also raises the centre of gravity, making the tractor less stable, or a little top heavy. Heavy implements or loads mounted on the rear of the tractor will shift the centre of gravity further to the rear making it easier to flip backwards. Crossing steep slopes can change the centre of gravity depending upon the angle of the slope. Front-end loaders are used in the agricultural and landscape industries to handle many types of material from feed and manure to soil and gravel. The versatility of loaders allows an operator to load, lift, transport and handle materials with great ease. Like other mechanical devices, safety lies with the operator and his knowledge of what the machine can and cannot do. A heavy load raised too high can change the centre of gravity and the stability of the tractor-loader combination. This can lead to situations where the tractor can tip over. There are a number of rules that an operator can follow to prevent such accidents from occurring: Keep the loader bucket low while transporting loads. As mentioned above, a raised bucket can change the centre of gravity of the tractor. Obstacles on the traveling surface such as rocks,boards,or holes in the ground could lead to a quick upset if the load is carried too high. Avoid traveling downhill with loaded buckets. Restrict your speed when traveling with a load. Remember, keep it low, travel slow. The added load which you carry in the bucket adds to the momentum of the tractor. If you were moving at a high speed and decided to turn it could flip you over. Keep your load even in the bucket. An uneven load could lead to dangerous situations. Your loader can only hand so much weight and you don't want to put undue stress on the various components. Check your operator's manual for the loader's capacity. Ballast will help give you stability. Extra ballast will help counter-balance the extra weight at the front of your tractor and reduce rollover potential. When not in use, remove your loader from the tractor. Having the loader always attached while trying to perform other duties with the tractor can make some situations complicated and lead to poor visibility and added fuel costs. Don't misuse your loader. The loader bucket was not meant to be used as a work platform for people. Hydraulics can fail leading to tragedy. When leaving your tractor-loader alone, lower the bucket to the ground. This is so that it cannot accidentally be lowered by children or others. Handling large round bales: A number of operators have been injured when improperly secured bales rolled down the arms of the front-end tractor loaders. Proper restraining devices should be used to prevent the bales from coming loose. A manufactured bale spear, specifically for this purpose is ideal. Remember:.Never work or walk under a raised loader. .Watch for overhead electrical wires and other obstacles when raising loaders. .Be careful near banks and slopes. Added weight can cause them to collapse. .Don't move or swing loads when people are working in the area. .Never allow anyone to pass under a raised bucket. .Keep the work area as flat as possible. .Match the proper bucket to the job you are doing. Case History: The victim was driving a loader tractor along the shoulder of a road with the bucket raised. The tractor ran off the shoulder and rolled over into the ditch. The victim was pinned underneath the tractor. Tractor rollovers account for about half of fatal tractor accidents, and are responsible for manydisabling injuries and considerable property damage. Overturns often result from operator distraction. Side Rollovers Rollovers to the side are the most common type of rollover. There are a number of ways that this type of overturn can occur.Driving across a steep slope: The greater the angle of the slop, the greater the danger will be of rollover. Your tractor was designed to distribute it's weight around the centre of gravity of the vehicle. If you cross a slope with a very steep angle there may be more weight on the downward side of the centre of gravity and the tractor could simply flip over. This problem is compounded by the fact that you may encounter obstacles which will change your stability such as potholes on the downhill side or rocks and other obstacles on the uphill side. Your tractor may also have side-mounted implements on it. You should keep the side-mounted implements on the uphill side of the slope for added stability. Don't raise the implements or loader buckets. Keep them as low to the ground as possible. Avoid turning uphill. If stability becomes uncertain, turn downhill. This could prevent a rear rollover. Driving too close to a ditch, culvert or pond can lead to the tractor rolling into the ditch if you get too close to the edge. A good rule of thumb is to stay as far away from the embankment as the ditch is deep. This keeps you behind the sheer line. The edge of a bank has little to hold it there and the weight of your tractor can cause the earth to sheer away along this line, causing you to slide into the ditch. Case History: The victim was cutting hay near the edge of an embankment. The tractor went over the edge and rolled on top of the victim, trapping the individual face down in approximately one foot of water. Turning while traveling too fast can result in a side rollover. As your vehicle travels faster it wants to continue on in the straight line in which you are heading. Without slowing down, if you make a sudden, quick turn, the weight of the tractor wants to keep going and causes it to flip over. Driving with a front-end loader too high changes the centre of gravity of your tractor. It raises the centre of gravity, making it 'top heavy'. A sudden turn or raising the tractor on one side can cause a side rollover. The problem is compounded when the loader has material in it, especially if it is not evenly distributed. Towing a load that is too heavy to control can cause jack-knifing. Case History: The victim was driving a tractor and bale wagon down a 40 degree slope. The wagon jackknifed, causing the tractor to roll over and pin the driver. Driving on roadways without locking rear brakes. If you do not lock your brake pedals together for travel on the roadway, should you need to apply them suddenly, you may only hit one pedal. If this occurs it could cause one wheel to lock up, leaving the other in motion. The result could cause you to swerve into the ditch or into oncoming traffic. Rear Rollovers Tractor rear rollovers are caused by:
Case History: The victim was using a tractor to pull out small trees on a relative's farm. A chain was wrapped around the base of the tree, and the other end was hitched to the rear of the tractor. The hitch point was higher than the tractor's rear axle. When an attempt was made to pull out the tree, the tractor flipped over backward and crushed the victim.
Driving forward when stuck in mud or ice can be dangerous. If the tires are frozen to the ground or will not move, you could end up with a rear rollover when power is applied. If you get mired in mud, try backing your tractor out first. This will keep the front end down and reduce the risk of rollover. If the tractor does not become free, then you may need to tow it out. Make sure that the towing vehicle is heavy enough for the job and that the tow lines are hitched to the drawbar. The towing tractor must have a rollover protective structure on it. The danger of rear rollover is especially significant when the tractor is towing of pulling a load with a chain or tow rope. As well as the possibility of a rollover occurring, there is danger in using tow ropes or cables. These items store energy by stretching under load. By jerking the rope or cable or making a running start to move a heavy stationary load can stress a nylon rope or cable to the breaking point. If it snaps, it will act like a stretched rubber band and sling back at the tractor. It could smash a cab's windows or even decapitate and operator. How can this type of fatality be prevented?
Not all cabs presently being sold for tractors are crush proof; check and make sure that a cab is crush proof (R.O.P.S.) and meets A.S.A.E. standards. Most major tractor companies have a low cost retro-fit roll-bar. The price for a roll-bar is insignificant when measured in terms of saving lives, or the pain and suffering resulting from serious injury. Falling from tractors is a common cause of serious injury and death. Falls are needless and preventable accidents. Falls occur from moving and parked tractors. Let's explore some methods for preventing these accidents. Mounting and Dismounting
Operator Falls Operators sometimes fall from tractors and are crushed under the wheels or mangled by trailing equipment. The following safety practices can help prevent such injuries:
Never operate the tractor while riding on the draw bar, sitting on the fender, standing on the steps, or sitting on the backrest of the operator's seat. Do not attempt to get on or off of the tractor while it is in motion. Although a tractor may appear to be moving slow enough to jump on or off, a slip can leave you crushed under the wheels before the operator can react. 2. Maintain safe operating speeds. Never drive so fast that the front wheels of the tractor bounce. Watch ahead for obstructions and avoid them. Slow down before making turns. Always watch where you are going, particularly when there may be obstacles such as tree limbs, ditches etc. Speed and obstacles don't mix well. You will often be tempted to use your tractor to transport a helper. Children often plead for rides. Do not give in. An unexpected bump or turn could toss an extra rider right out the cab door and off the tractor. Your passenger cannot anticipate every tractor movement and brace against it. Furthermore, all the vibration and bumps are transmitted to the passenger. He can easily lose his grip and fall off. Passengers can cause other problems, too. They can interfere with your operation of controls, they can accidentally move controls themselves, and they frequently distract the operator's attention. Many people think an extra rider is safe in the cab of a tractor, but in an accident the extra rider may be tossed around, hit the door, and be thrown out. Make exceptions to the 'no extra rider' rule only under these conditions: when a second seat is provided on the tractor or instructions are being given or received. There is potential danger for the instructor while training a new operator, but the training is essential. The danger can be minimized by driving at a slow speed and on level ground. MAKE 'NO RIDERS' THE RULE - NOT THE EXCEPTION Case History: The victim was riding on the fender of a tractor driven by their spouse. An attached rotary mower was cutting grass. As the tractor came close to a pine tree, branches knocked the victim off the tractor and into the path of the mower. The tractor could not be stopped in time, and the mower ran over the victim. One of the main reasons for tractor accidents is the difference in speeds between cars and tractors. The closure time - that is the time it takes for one vehicle to overtake another - is much less for farm machinery than with automobiles. The short closure time means the driver of a passenger vehicle has but a few seconds to identify the tractor and react accordingly. This is why positive identification of slow-moving vehicles is important. The accompanying diagram illustrates this situation.
Before taking your tractor on the highway, you should ensure that it is prepared for such a trip and that your combination of vehicles conforms to the highway regulations where you will be operating. Under the ONTARIO HIGHWAY TRAFFIC ACT, your farm tractor is not a motor vehicle but it is considered a vehicle. Registration plates are not required for farm tractors, farm implements or self-propelled implements of husbandry when traveling from farm to farm for farming purposes, or places necessary for repair or maintenance. Insurance coverage for the above mentioned vehicles is usually included in the farm insurance policy. Safe farm equipment road travel requires knowledge of traffic rules, maturity and common sense. The SLOW MOVING VEHICLE (SMV) SIGN is used to warn other road users that the vehicle displaying the sign may be a vehicle traveling slower than the normal speed of traffic. Every farm tractor or self-propelled implement of husbandry, when operating on a highway, or any vehicle towed by either of them must have a slow moving vehicle sign attached to the rear, except when directly crossing a highway. Always be seen! Remember that the SMV sign is for your safety.
It must be clearly visible for a distance of not less than 150 meters The SMV colours deteriorate through exposure to the sun and weather. To ensure that the sign is clearly visible to other road users, it should be replaced when faded or damaged.
* Your visibility is vital at all times. Always use your lights when it is dark or visibility is poor. Many collisions occur due to the fact that other motorists do not see you in advance. Lights are required in Ontario on a highway at any time from one-half hour before sunset to one-half hour after sunrise and at any other time when due to insufficient light or unfavorable weather conditions, persons and vehicles on a highway cannot be seen clearly at a distance of 150 meters A farm tractor or self-propelled implement of husbandry if fitted with an electric lighting system must display two white lights on the front of the vehicle and at least one red light on the rear of the vehicle. The lights must clearly be visible at a distance of 150 meters If the vehicle is not equipped with electric lighting, a lamp or lamps should be placed on the left side of the vehicle with at least one white light to the front and one red light to the rear. Case History: The victim was taking an orchard sprayer along a road. The tractor was illuminated with headlights plus a rear-mounted halogen working lamp. However, the sprayer wasn't fitted with either a lighting system or a slow moving vehicle sign. As a car approached from the rear, its driver assumed that the halogen working light was an oncoming vehicle. The driver moved the car towards the should of the road because the light appeared to be crowding the centre line. The car struck the back of the sprayer, causing the tractor to roll over onto its roof. The victim was ejected from the tractor.
The PTO spins at speeds fast enough to wrap a person up in it before they know what happened. All it takes is a thread, shoestring, raveled jeans, or even long hair to get a person wrapped up in this powerful piece of machinery. A 540 rpm PTO shaft will rotate nine times in one second and travel 2.17 meters This means that if a bootlace catches on the PTO shaft that in one second almost 2.17 meters of lace will be wrapped up before you can even react! A 1000 rpm PTO shaft will rotate 16.7 times and travel four meters in one second! Never remove shields from a PTO shaft. Even PTO shafts with guards are dangerous to step over. To be safe, walk around your equipment. The extra few seconds taken will help to insure you of more years of life. An unguarded PTO shaft is dangerous. It can catch on your clothing before you realize it. If you're lucky, your clothes will tear, freeing you without serious injury. If you're not so lucky, you could be strangled or mutilated by the high-speed shaft. Master shields help to prevent accidental contact with the tractor stub shaft and the front universal joint of the attached machine's driveline. PTO shaft guards are provided for many tractors to completely enclose the tractor stub shaft when the PTO is not being used. A PTO rolling shield completely encloses the PTO shaft. These shields are metal or plastic tubes supported on bearings so the shields rotate independently of the shaft. When the PTO shaft is turning, they rotate with it. But if a person contacts the shield, the rotating shield stops while the shaft inside continues to spin. To prevent injury from entanglement with the power take-off shaft, follow these safety rules:
The measurement of sound or noise is related to pressure, frequency and duration, and is commonly measured in units called decibels. With continual exposure to excessive noise, the ability to hear normal conversation is impaired. Noise is too loud when:
If you do not have a cab that reduces noise significantly you may need to wear hearing protection in the form of ear plugs or muffs designed to block out harmful noise levels. Better tractor design means fewer hazards. Yet any machine can be dangerous if recommended operating procedures are ignored. A quick turn or one-wheel braking during high speed travel can tip a tractor sideways. Pop the clutch with a heavy load behind, and your machine could tip over backward. Failure to disengage the PTO before cleaning or adjusting machinery could result in mutilation or death.Safety practices begin with YOU. To be safe..... you need to think safe. Farming is one of the most hazardous occupations. Accident prevention requires a constant, conscious effort by those involved in farming. Here is a list of some things you can do to help prevent accidents: No short cutsMany accidents happen while trying to save a few seconds or a few steps. There are no short cuts to safety. Operate your equipment the safe way, the right way.Take a breakOther accidents happen when a farmer is over tired. Long hours involved in a repetitive task, like driving a tractor down a long field, can be very fatiguing. Taking a short break will help keep your mind, and your muscles, more alert.Reduce stressFarming can be extremely stressful. It seems there are always deadlines to beat and never enough time to do a job right. People rarely work well under stress. Talking about your problems, planning ahead and remaining flexible will help to reduce stress and improve clear thinking.Know your equipmentBe familiar with all equipment you operate. Also, instruct all drivers on the safe operation of farm machinery by going over the operator's manual. Know the equipment's potential and limits. Use the equipment as it was developed.It's Up To YouSafe tractor operation involves consideration of many details. Your owner's manual contains the information you need to be a responsible, safe operator. Knowledge, skill and common sense are your weapons in the war against tractor accidents.TRACTOR SAFETY QUIZ The correct answer for each of the following statements is TRUE or FALSE. Please make your selection. ____1. Refueling an engine presents no danger of fire if it is shut off. ____2. To inspect for leaks in hydraulic lines, run your hands over the hoses. ____3. Hand holds are placed on tractors for extra riders. ____4. Always shut off the engine and apply the parking brake before dismounting the tractor. ____5. All PTO shafts should be guarded with the proper shielding. ____6. Tractors may be started safely only from the operator's seat. ____7. Noise levels of 100 decibels on a tractor are considered safe for an 8 hour exposure. ____8. When traveling, the front-end loader should be positioned high for good visibility. ____9. Weights help keep the front end of the tractor down. ____10. Proper training is essential for safe tractor operation. ____11. Tractor upsets are a leading cause of tractor fatalities. ____12. It is alright to drill holes in a ROPS frame to mount a CB radio. ____13. Hitch pins should always have proper safety catches to prevent accidental unhitching. ____14. When towing a load, go down the hill in the same gear as you would go up a hill. ____15. It is not necessary to use a seat belt when the ROPS is built into the cab. ____16. When driving your tractor on the roadway, you must have a slow-moving vehicle sign on the rear of the tractor. ____17. A tractor operator must be sixteen years of age to drive on the highway in Ontario. ____18. Be sure the highway is clear of traffic before pulling into it. ____19. When towing equipment on the highway, you must have a proper safety chain hook-up. ____20. When pulling a load up a slope, keep the hitch as high as possible. ____21. When stuck in the mud try to back out first. ____22. The position of a tractor's loader changes the centre of gravity as the position of the loader changes. ____23. Three is the maximum number of riders allowed on a tractor. ____24. If you are working with a tractor with rollover protection, always wear your seatbelt. ____25. Always read the operator's manual before operating a new tractor. ____26. A tractor can flip completely backwards in about 1.5 seconds. ____27. Do not make sharp turns at high speeds. ____28. If tractor stability becomes uncertain on a slope, turn downhill. ____29. In Ontario, you are required to signal your intention to turn when operating a tractor on a roadway. ____30. Check your tires and wheels for proper pressure and tread regularly. 1. F 2. F 3. F 4. T 5. T 6. T 7. F 8. F 9. T 10. T 11. T 12. F 13. T 14. T 15. F 16. T 17. T 18. T 19. T 20. F 21. T 22. T 23. F 24. T 25. T 26. T 27. T 28. T 29.T 30. THere are the correct answers to the questions marked false: TRACTOR AND WAGON EXERCISE - Total Points: 400/300 for skill and safety plus 100 for time (Time Limit: 20 minutes) The following is a brief description of how the competition works: The judge for this exercise will start recording the time by means of a stop watch, once he/she has handed the keys for the tractor to the contestant. The contestant will then mount the tractor (in parking station). He/she must always remember to use the three point method whenever he/she mounts or dismounts from the tractor. He/she must never jump on or off the tractor. The judge will look for any loose clothing on the contestant, such as open shirts, coats, untied shoe laces, etc. Once the contestant has mounted the tractor, he/she is to put his/her seat belt on. He/she will then start the tractor, having first checked to see if it is in the "park" position, and that the clutch has been disengaged. Once the tractor is in motion, he/she will depress the brake pedal to check to see if the tractor has brakes. He/she will then proceed to the wagon station. The contestant must back the tractor up to the wagon, so that the draw bar is in the exact position for the contestant to swing the wagon tongue into position and freely drop the draw pin in. He/she will not be allowed to manually move the tractor or wagon to assist with the hook-up. The contestant will hook-up the safety chains on the wagon on to the tractor, remove the slow moving vehicle sign from the tractor and place it on the rear of the wagon. He/she will then remove the wheel blocks from the right hand rear wheel of the wagon, and place them on the wagon. The contestant will then mount the tractor and proceed to enter the course as specified ion the diagram layout. He/she must travel at a safe speed to allow him/her to maneuver between the five gates on the right hand side of the course. A predetermined amount of points will be deducted for each ball knocked off, and each stake knocked over. He/she will be allowed 40 feet at the end of the course to make his/her turn, to allow entry through the five gates on the left hand side, which are the same as those for the right hand side. On passing through the last gate on the left hand side, the contestant will drive the tractor into the wagon park station area, and directly through the two guide stakes, which allow for three feet of clearance on each side of the wagon. The front wheels of the tractor must be ahead of the front two guide stakes before he/she commences to back the wagon up to the wagon park position area. For each consecutive attempt to back the tractor and wagon up to the parking station, points will be deducted. Because the back of the wagon will be covered with an 8' x 4' sheet of plywood, it may be necessary for the contestant to stop the tractor and get off to check to see just how close he/she is to the stakes at the rear of the wagon. He/she must also be careful not to cramp the wheels of the wagon, or points will be deducted. The wagon must be in the centre of the parking station, and within 6" of the stakes at the rear of the wagon. For each inch that the wagon is off centre, and for each inch that the wagon is further away than 6" from the rear stakes, points will be deducted. The contestant must be very careful not to knock the ball off of the rear of the wagon, because he/she will lose in excess of 100 points if he/she does. Once the wagon has been parked, the contestant will then take the blocks off the wagon and put them behind and in front of the rear wheel of the wagon. He/she will then proceed to unhook the wagon (safety chains and draw pin). The draw pin is to be left in the tractor draw bar. The contestant will then take the slow moving vehicle sign from the rear of the wagon and attach it to the tractor. He/she will then return the tractor to the parking station, by backing it up to the stake. He/she must remember to put the tractor in "park", and to take the keys out of the tractor and hand them to the judge. The stop watch will then be stopped, and the time recorded. Each contestant will be required to supply his/her own hard hat, leather gloves, hearing protection (ear muffs), and safety boots for this exercise. The safety boots must be in good shape and have steel toes. 1 - tractor, complete with rollover protection and seat belts.1 - Wagon running gear complete with bolster. Flat bed is 16 to 18 feet long and 8 feet wide. Rear of the flat bed is to be covered with a 4 x 8 sheet of plywood. The running gear is to be extended to 120 inches from the centre of the front axle to the centre of the rear axle. The wagon bed is to be placed on the running gear so that the measurement from the front of the wagon to the front axle is approximately 33". Space requirements for this exercise, approximately 210' x 80'. Surface requirements - ideally, the competitions should be run on a paved surface. Procedure for Scoring10 minutes or less is a perfect score = 100 points 10 minutes, 1 second to 11 minutes = 80 points 11 minutes, 1 second to 12 minutes = 60 points 12 minutes, 1 second to 13 minutes = 50 points 13 minutes, 1 second to 14 minutes = 40 points 14 minutes, 1 second to 15 minutes = 30 points 15 minutes. 1 second to 16 minutes = 20 points 16 minutes, 1 second to 17 minutes = 10 points 17 minutes, 1 second to 20 minutes = 0 points Failure to complete the above-mentioned exercise in a time limit of 20 minutes will mean the automatic disqualification of the contestant. The time starts as soon as the contestant takes the keys from the clockman. The time ends as soon as the contestant hands the keys to the clockman, or walks away from the tractor without the keys.
Total points 150 (Perfect score) minus __________________{demerit points}= _________________
The Farm Safety Association maintains a video lending library in Guelph, Ontario. The following tractor safety videos are available from the Association by calling (519) 823-5600: VT 042 "Accidents Are Seldom Accidents" 21 minutes - colour - 1974 Available on VHS This video emphasizes the need for roll-over protection on tractors and also illustrates many safe operating procedures for tractors. Produced by Massey-Ferguson, Great Britain. VT 043 "Farm Tractor Safety" 11 minutes - colour - 1976 Available on VHS Devoted to the positive aspects of tractor safety, this video shows tractor overturn tests followed operator precautions to avoid side and rear overturns. Importance of ROPS is emphasized along with PTO safety, extra rider hazards, fuel handling safety, and safe highway transport. Produced by International Harvester, U.S.A. VT 093 "Horsepower" 9:45 minutes - 1989 Available in VHS only This video looks at tractor safety and features farmers who have experienced accidents while operating their tractors. Produced by the Nova Scotia Farm and Home Safety Committee
VT 115 "It Won't Happen To Me (Tractor Safety)" Time: 16 minutes The basics of tractor safety are covered using Farm Safety Association's fatalities as examples of what can go wrong and lead to fatal situations. Emergency medical personnel are also interviewed about tractor accidents.
Produced by New Holland, 1995 VT 126 "Nellie the Farm Safety Dog" Time: Approximately 7 minutes This true story is about a tractor rollover accident which occurred on a Southern Ontario tobacco farm. Nellie, the resident dog on the farm brought help to save the farmer's life. The rescue is recounted by those involved including police and ambulance drivers. Produced by the Ontario Ministry of Agriculture, Food and Rural Affairs S 028 "Safe Use of Farm Tractors" 65 slides - audio tape and transcript - 1982 Tractors by far are the most common type of machinery used on a farm. Tractor related accidents also cause the majority of farm-related fatalities. This slide set discusses the safe operation of farm tractors, with particular emphasis on tractor roll-overs. Produced by Agricultural Extension Service, University of Minnesota. VT 044 "Target You - Tractor Safety" 10 minutes - colour - 1979 Available in VHS This video is largely animated and by means of the principal character "Gotta-Go Joe", demonstrates many of the common accidents that a farmer can become involved in with his tractor, by trying to beat the clock.
Produced by John Deere Ltd. VT 123 "Tractor Rollovers and ROPS" Time: 6 minutes 30 seconds Available in VHS only This video outlines the importance of having your tractor protected with a Rollover Protective Structure and covers ways that John Deere has made it easier to add this protection to your tractor. Produced by John Deere VT 051 "Tractor Safety" 21 minutes - colour 1977 Available in VHS only This video covers all the basics of safe tractor operation. Produced by Perdue University. VT 129 "Tractor Safety on the Farm" Time: 11 minutes 30 seconds
This video covers the basics of tractor safety including the pre-operational check, starting and stopping; operation of the tractor including rollover situations; power takeoff safety and travel on public roadways. Produced by the Farm Safety Association Inc, 1994 VT 092 "Tractor Tips" 17 minutes - colour 1990 Available in VHS only Shows tractor operation and management techniques that reduce fuel consumption in field operations. Discusses safe ballasting, gearing up-throttle down and equipment matching. Produced by Independent Study, University of Guelph VT 045 "Tractor Safety Begins With You" 20 minutes Available in VHS only This video depicts a number of situations which led to tractor accidents happening involving extra riders, the P.T.O. and rollovers. Produced by Kubota. VT 101 "Tractor Safety Is No Accident" 15 minutes - colour - 1982 Available on VHS A professional airline pilot who is also a farmer narrates this video on tractor safety. The narrator applies the same reasoning in operating tractors as he does with airplanes. A number of important areas are covered such as: the walk around check; tractor rollovers; transporting equipment; P.T.O. safety; extra riders; maintenance and service. Produced by International Harvester, Chicago, Illinois, U.S.A. VT 046 "Why Did Tommy Die?" 10 minutes - colour - 1980 Available on VHS A number of young people are killed each year by tractors. Through the video's characters, John, Merriam and Tommy, the video explores the principle causes of tractor injuries and fatalities. The video demonstrates tractor fires, P.T.O. accidents, and tractor rollovers. Produced by the Ontario Ministry of Agriculture and Food. VT 047 "Within The Frame of Safety" 6 minutes - colour - 1969 Available on VHS This video details the designing, testing and development of a protective frame for tractors. These structures when used in conjunction with seat belts, help prevent injuries due to side-rolls or back-flips. Produced by International Harvester, U.S.A.
PTO Driven Equipment
Farm Safety Association Inc. 22-340 Woodlawn Road West, Guelph, Ontario N1H 7K6 (519) 823-5600 Fax: (519) 823-8880 Ontario Ministry of Agriculture,Food and Rural Affairs Farm Safety Association Home Page Added to the database: 1999 Disclaimer and Reproduction Information: Information in NASD does not represent NIOSH policy. Information included in NASD appears by permission of the author and/or copyright holder. More |