What is a DHCPv4 address assignment method that assigns IPv4 addresses for a limited lease period?

Course Hero uses AI to attempt to automatically extract content from documents to surface to you and others so you can study better, e.g., in search results, to enrich docs, and more. This preview shows page 13 - 16 out of 42 pages.

Last Updated on November 8, 2022 by InfraExam

CCNA2 v6.0 Chapter 8 Exam Answers 2018 2019

unicast DHCPACK
broadcast DHCPACK
unicast DHCPREQUEST

broadcast DHCPREQUEST

Explanation:

When a DHCP client receives DHCPOFFER messages, it will send a broadcast DHCPREQUEST message for two purposes. First, it indicates to the offering DHCP server that it would like to accept the offer and bind the IP address. Second, it notifies any other responding DHCP servers that their offers are declined.

FF-FF-FF-FF-FF-FF and 255.255.255.255
both MAC and IPv4 addresses of the DHCP server
MAC address of the DHCP server and 255.255.255.255

FF-FF-FF-FF-FF-FF and IPv4 address of the DHCP server

Explanation:

When the lease of a dynamically assigned IPv4 address has expired, a workstation will send a DHCPDISCOVER message to start the process of obtaining a valid IP address. Because the workstation does not know the addresses of DHCP servers, it sends the message via broadcast, with destination addresses of FF-FF-FF-FF-FF-FF and 255.255.255.255.

- manual allocation
- pre-allocation
- automatic allocation
- dynamic allocation
  
  Explanation:
  Dynamic allocation is the most commonly implemented allocation mechanism. It leases the IP parameters for a predefined period of time.
- client IP address
- client hardware address
- gateway IP address
- broadcast MAC address
  
  Explanation:
  When a DHCPv4 client does not have an IPv4 address, a DHCPv4 server will send a DHCPOFFER message back to the client hardware address of the requesting DHCPv4 client.

DHCPDISCOVER
DHCPOFFER
DHCPREQUEST

DHCPACK

Explanation:

When a DHCP client lease is about to expire, the client sends a DHCPREQUEST message to the DHCPv4 server that originally provided the IPv4 address. This allows the client to request that the lease be extended.

It will allow DHCPDISCOVER messages to pass without alteration.
It can forward both broadcast and multicast messages on behalf of clients.
It can provide relay services for multiple UDP services.

It reduces the response time from a DHCP server.

Explanation:

By default, the ip helper-address command forwards the following eight UDP services:Port 37: Time Port 49: TACACS Port 53: DNS Port 67: DHCP/BOOTP client Port 68: DHCP/BOOTP server Port 69: TFTP Port 137: NetBIOS name service

Port 138: NetBIOS datagram service

The Cisco router will exclude 15 IP addresses from being leased to DHCP clients.
The Cisco router will allow only the specified IP addresses to be leased to clients.
The Cisco router will exclude only the 10.0.15.1 and 10.0.15.15 IP addresses from being leased to DHCP clients.
The Cisco router will automatically create a DHCP pool using a /28 mask.

Explanation:
The ip dhcp excluded-address command is followed by the first and the last addresses to be excluded from being leased to DHCP clients.

configuring the router to act as a DHCPv4 server
configuring the router to obtain IP parameters from a DHCPv4 server
configuring the router to act as a relay agent
configuring the router to resolve IP address conflicts

Explanation:
The ip address dhcp command activates the DHCPv4 client on a given interface. By doing this, the router will obtain the IP parameters from a DHCPv4 server.

The router is intended to be used as a SOHO gateway.
The administrator needs the router to act as a relay agent.
The router is meant to provide IP addresses to the hosts.
This is an ISP requirement.
The router has a fixed IP address.

Explanation:
SOHO routers are frequently required by the ISP to be configured as DHCPv4 clients in order to be connected to the provider.

the all-routers multicast address
the link-local address of the router interface that is attached to the network
the unique local address of the router interface that is attached to the network

the global unicast address of the router interface that is attached to the network

Explanation:

When a PC is configured to use the SLAAC method for configuring IPv6 addresses, it will use the prefix and prefix-length information that is contained in the RA message, combined with a 64-bit interface ID (obtained by using the EUI-64 process or by using a random number that is generated by the client operating system), to form an IPv6 address. It uses the link-local address of the router interface that is attached to the LAN segment as its IPv6 default gateway address.

It should contact a DHCPv6 server for all the information that it needs.
It should use the information that is contained in the RA message exclusively.
It should use the information that is contained in the RA message and contact a DHCPv6 server for additional information.

It should contact a DHCPv6 server for the prefix, the prefix-length information, and an interface ID that is both random and unique.

Explanation:

ICMPv6 RA messages contain two flags to indicate whether a workstation should use SLAAC, a DHCPv6 server, or a combination to configure its IPv6 address. These two flags are M flag and O flag. When both flags are 0 (by default), a client must only use the information in the RA message. When M flag is 0 and O flag is 1, a client should use the information in the RA message and look for the other configuration parameters (such as DNS server addresses) on DHCPv6 servers.

DHCPv6 SOLICIT
DHCPv6 REQUEST
DHCPv6 ADVERTISE

DHCPv6 INFORMATION-REQUEST

Explanation:

In stateless DHCPv6 configuration, a client configures its IPv6 address by using the prefix and prefix length in the RA message, combined with a self-generated interface ID. It then contacts a DHCPv6 server for additional configuration information via an INFORMATION-REQUEST message. The DHCPv6 SOLICIT message is used by a client to locate a DHCPv6 server. The DHCPv6 ADVERTISE message is used by DHCPv6 servers to indicate their availability for DHCPv6 service. The DHCPv6 REQUEST message is used by a client, in the stateful DHCPv6 configuration, to request ALL configuration information from a DHCPv6 server.

SLAAC
stateless DHCPv6
stateful DHCPv6

RA and EUI-64

Explanation:

Stateless DHCPv6 allows clients to use ICMPv6 Router Advertisement (RA) messages to automatically assign IPv6 addresses to themselves, but then allows these clients to contact a DHCPv6 server to obtain additional information such as the domain name and address of DNS servers. SLAAC does not allow the client to obtain additional information through DHCPv6, and stateful DHCPv6 requires that the client receive its interface address directly from a DHCPv6 server. RA messages, when combined with an EUI-64 interface identifier, are used to automatically create an interface IPv6 address, and are part of both SLAAC and stateless DHCPv6.

It sends an ARP message with the IPv6 address as the destination IPv6 address.
It checks with the IPv6 address database that is hosted by the SLAAC server.
It contacts the DHCPv6 server via a special formed ICMPv6 message.

It sends an ICMPv6 Neighbor Solicitation message with the IPv6 address as the target IPv6 address.

Explanation:

SLAAC is a stateless allocation method and does not use a DHCP server to manage the IPv6 addresses. When a host generates an IPv6 address, it must verify that it is unique. The host will send an ICMPv6 Neighbor Solicitation message with its own IPv6 address as the target. As long as no other device responds with a Neighbor Advertisement message, then the address is unique.

the MAC address of the IPv6 enabled interface
a randomly generated 64-bit hexadecimal address
an IPv6 address that is provided by a DHCPv6 server

an IPv4 address that is configured on the interface

Explanation:

The EUI-64 process uses the MAC address of an interface to construct an interface ID (IID). Because the MAC address is only 48 bits in length, 16 additional bits (FF:FE) must be added to the MAC address to create the full 64-bit interface ID.

EUI-64
random generation
stateful DHCPv6
DAD
ARP

Explanation:
A host that is using SLAAC has two means to configure an interface ID: EUI-64 and random generation by the host operating system.

CCNA 2 RSE 6.0 Chapter 8 Exam Answers 2018 2019 03

SLAAC
stateful DHCPv6
stateless DHCPv6

static link-local

Explanation:

Stateful DHCPv6 pools are configured with address prefixes for hosts via the address command, whereas stateless DHCPv6 pools typically only contain information such as DNS server addresses and the domain name. RA messages that are sent from routers that are configured as stateful DHCPv6 servers have the M flag set to 1 with the command ipv6 nd managed-config-flag, whereas stateless DHCPv6 servers are indicated by setting the O flag to 1 with the ipv6 nd other-config-flag command.

CCNA 2 RSE 6.0 Chapter 8 Exam Answers 2018 2019 02

Add the ipv6 dhcp relay command to interface Fa0/0.
Configure the ipv6 nd managed-config-flag command on interface Fa0/1.
Change the ipv6 nd managed-config-flag command to ipv6 nd other-config-flag.

Add the IPv6 address 2001:DB8:1234:5678::10/64 to the interface configuration of the DHCPv6 server.

Explanation:

Client DHCPv6 messages are sent to a multicast address with link-local scope, which means that the messages will not be forwarded by routers. Because the client and server are on different subnets on different interfaces, the message will not reach the server. The router can be configured to relay the DHCPv6 messages from the client to the server by configuring the ipv6 dhcp relay command on the interface that is connected to the client.

CCNA 2 RSE 6.0 Chapter 8 Exam Answers 2018 2019 04

No virtual link-local address is configured.
The Duplicate Address Detection feature is disabled.
The router is configured for SLAAC DHCPv6 operation.

The router is configured for stateless DHCPv6 operation

Explanation:

The router is configured for stateless DHCPv6 operation, which is shown by the last two lines of the show command output. Hosts will configure their IPv6 addresses by using the prefix information that is provided by RA messages. They will also obtain additional configuration information from a DHCPv6 server. The “No virtual link-local address” option and the “Duplicate Address Detection” option are irrelevant to DHCP configuration. Option “SLAAC configuration” is incorrect because by definition SLAAC will use only the information that is provided by RA messages to configure IPv6 settings.

CCNA 2 RSE 6.0 Chapter 8 Exam Answers 2018 2019 01

The GigabitEthernet interface is not activated.
The router is configured for SLAAC operation.
The DNS server address is not on the same network as the clients are on.

The clients cannot communicate with the DHCPv6 server, evidenced by the number of active clients being 0.

Explanation:

The router is configured for SLAAC operation because there is no configuration command to change the RA M and O flag value. By default, both M and O flags are set to 0. In order to permint stateless DHCPv6 operation, the interface command ipv6 nd other-config-flag should be issued. The GigabitEthernet interface is in working condition because clients can get RA messages and configure their IPv6 addresses as expected. Also, the fact that R1 is the DHCPv6 server and clients are getting RA messages indicates that clients can communicate with the DHCP server. The number of active clients is 0 because the DHCPv6 server does not maintain the state of clients IPv6 addresses (it is not configured for stateful DHCPv6 operation). The DNS server address issue is not relevant to the problem.