Wireless wps wlan verstärker n wifi repeater 300 mbit ap rohs client baytter

Wi Fi Repeater

LED Explanation

Button Explanation

WPS Button: If your host router supports WPS function, you can press the WPS button and then press the WPS button of the WiFi Repeater to establish a secure connection between the host router and the WiFi Repeater.

Reset Button: This button is used to restore The Repeater’s factory default settings.With the Repeater powered on, use a pin to press and hold the Reset button for about 8 seconds.

LAN Port: One 10/1 00Mbps RJ45 Ethernet port is used to connect an Ethernet-enabled device to a Wi-Fi network, such as Internet TV, DVR, Gaming console and so on. Please note that this port cannot be connected to a router.

Quick Installation

1. Power On

Plug in next to your router, wait until the WALAN LED is blinking.

2. Connect

For  Windows Users

Disconnect your Ethernet (wired) connection from your computer. Click the Wi-Fi icon on the taskbar and connect to the Repeater’s network (e.g. WiFi-Repeater).

For Mac OS X Users

Disconnect the Ethernet (wired) connection from your computer (if any). Click the Wi-Fi icon in the top right corner of the screen, and connect to the Repeater’s network (e.g. WiFi-Repeater).

For Wired

Disable the Wi-Fi on your computer. Connect your computer to the Repeater via an Ethernet cable.

3. Configure the Repeater Mode

1.Launch a web browser and type http://myrepeater.net or http://1192.168.10.1 in the address field. Enter ad min (all lowercase) for both Username and Password, then click Login.

2. After logging in, you will see the web page below:

Click on “Repeater” to continue.

3. Select your Wireless router’s Network. Either keep the default SSID or customize it for extended network and insert the key of your network.

Note: The default Repeater ssid is set to be xxx ext(xxx indicates host Router’s SSID) and the Security Key is the same as your host Router’s WiFi key.

4. Click on “Apply” button, The Wi-Fi Repeater will restart. After the reboot has been completed, the Wi-Fi Repeater is accessible under the SSID and the Wireless key.

Use the Repeater as a Network Adapter

The Repeater can be used as a wireless adapter to connect any Ethernet enabled device, such as a Blu-ray player, game console, DVR, or smart TV, to your wireless network.

After the Repeater connected to the Internet, you can connect an Ethernet-only device to the Repeater using an Ethernet cable.

Ethernet Connection

4. Relocate

Plug in the Repeater halfway between your router and the Wi-Fi dead zone.

Enjoy!

The Repeater Wifi-Repeater to the end of the host network’s 55ID and uses the same Wi-Fi password.

Configure the AP Mode

1. Follow process 1 ~3.1,After logging in, you will see the web page below:

2. Change the SSID and Password, Click on “Apply” button, The Wifi Repeater will restart.

3. After the Repeater reboot has been completed, connect it to your router’s Ethernet port with an Ethernet cable.

6. Using WPS

WPS is an easier way to extend your host network. You are recommended to use this method if your host router has a WPS button.

Note: your host router should support WPS.

The button might look like one of these:

Otherwise, please setup Using a Web Browser.

1. Press the WPS Button on your host Router
2. Press and hold the WPS Button on the side of the Wifi Repeater for one second within 2 minutes.
3. If the connection is successful, The default Repeater ssid is set to be xxx ext(xxx indicates host Router’s 551
4. and the Security Key is the same as your host Router’s WiFi key.

7. Change Management password

Default password of the Wifi Extender is ‘ad min”, and it’s displayed on the login prompt when accessed from web browser There’s a security risk if you don’t change the default password, since everyone can see it. This is very important when you have wireless function enabled.

1. Click “Manage-> Password” located at the home page, the following message will be displayed on your web browser.

2. Click Save to save the settings.

8. Factory Default and Settings Backup, Restore

You can backup all Setting of this router to a file, so you can make several copied of router configuration for security reason.

Click “Manage-> Save/Reload setting ” located at the home page, the following message will be displayed on your web browser

9. Firmware Upgrade

1 )Get from your service provider firmware file.
2)Click “Manage-> Upgrade Firmware” located at the home page.

3)Make sure the firmware version is the same as the hardware version, then click “Browse” to select the firmware file.

4)Click “Upgrade”. The upgrade process takes a few minutes to complete and the Repeater will automatically reboot itself when finished.

FAQ(Frequently Asked Questions)

Q1 .What should I do if I cannot access the Repeater’s web management page?
A 1: Make sure your computer is connected to the extended network.
A2: Make sure your computer is set to obtain an IP address automatically.
A3: If the Repeater has connected to the router, you should go to your router’s DHCP client list to obtain the  Repeater’s current IP address.
A4: Reset the Repeater

Q2.Why does the wireless transmission rate speed down, while the wireless signal is stronger after repeated by the Repeater?
A 1 : In compliance with the wireless transmission protocol, all the Repeater devices are set to work in half-duplex instead of full-duplex mode. In other words, the Repeater has to process one-way communication between your root Wireless router (or AP) and the terminal clients; so the transmission time will be double-increased, while the speed will be decreased. Recommends that you connect to the extender when your home network connection is poor, or when you want a larger wireless coverage to eliminate “dead zones”.

Q3.Why the devices connected to the Repeater cannot get an IP address from the Repeater and cannot access the Internet.
A 1: Maybe you enabled a wireless MAC filter, wireless access control, or access control list (ACL) on your router. To solve this problem, please log into your router and disable the MAC filter, wireless access control or ACL.
A2: Maybe the Repeater has not been successfully connected to your router, please reset the Repeater and Reconfiguration.
A3: Maybe the IP address of the router is occupied or the wireless device connected by the router has reached the limit. please reboot your router, then reset the Repeater and Reconfiguration.

Very difficult to get to admin. got there finally but after setting it i can’t access it anymore. how do i access admin?

Hold reset button in for 20 sec
Then searcj with your phone again. Then connect to it.via a browser. Type in http://192.168.10.1. Go. It should connect to the setup software in the repeater
Their set up software doesn’t work cotrectly. Get your money back.

I’m needing to boost range outside for security camera my router is upstairs and camera is outside of garage do you think this me reach

it will work but you might need longer antenna for the camera that is what i did for mine

Compatible with the Arris TM 1602?

yes

What is the extended range of router superbooster/repeater?

I am not sure. I have one repeater in the family room, which is about 50 feet away from my office, which is where I have the other one.

Can I get a refund????

Read the refund policy. It depends on where you got it and how you paid for it.

Documents / Resources